All

How to Clean a Vape Tanks & Coils

The easiest method to get the most out of your vape is to make sure it’s clean. Vape juice’s components won’t damage your vaporizer, but the residue they leave behind will slow down the device’s efficiency over time. A clogged coil produces less flavor and vapor, and might make your e-cigarette taste like it’s been burned.

Changing the coil head may not remove the taste from your device that was leftover from your previous juice. A thorough cleaning is an easy method for new or old devices to ensure the greatest possible experience. Many people have questions about how often to replace your vape tank, so the answer is that it depends completely on your usage of it. Moreover if it’s been more than two years since you last changed your vape tank, it’s probably time to do it.

How To Clean a Vape Tank

To thoroughly clean a tank, you’ll need to dismantle it fully. O-rings are very important to keep track of while dismantling tanks, so be sure to note where each piece goes. In a small bowl, combine all of the ingredients and follow one of the following instructions.

  • Regular Rinse

This is the simplest and most usual way to clean your tank. A paper towel and running water are needed to clean the tank’s components after disassembly thoroughly. There may be more work if your tank isn’t clean or was already somewhat muddy when you initially got it. Then take each component, rinse it separately, and dry it with a paper towel. As previously mentioned, let the tank dry thoroughly so that no fog is evident. Use a blow dryer to speed things up, but be cautious not to damage any o-rings by overheating.

  • PG Rinse

Propylene Glycol may be used in place of water in the standard rinse technique (PG). Once you’ve filled your tank with PG, let it there for a few hours before draining it. Please remove all components and lay them out on a paper towel to dry. The cleaning procedure will be significantly more difficult if you use Vegetable Glycerin (VG), a heavier liquid.

  • Cleaning Agent Rinse

A cleaning product can provide better results if you’re looking for a more thorough clean. You should, however, be careful to rinse them fully and allow them to dry thoroughly after that. Using vinegar to clean may be beneficial, but you’ll need to rinse to remove any leftover odor properly.

  • Going Ultrasonic

An ultrasonic cleaner is an excellent option if you’re trying to clear up a mess piling up for some time. They are typically used to clean expensive metals and jewelry, but lately, ultrasonic cleaners are being utilized by vapers since they are so effective. The ultrasonic cleaning you use for your vape equipment doesn’t matter as long as it has a cycle time of at least ten minutes.

How To Clean Coils

This may be a lot more difficult than cleaning your tank, and it may be more cost-effective in the long run to replace the coils. To some extent, how you go about cleaning a replacement coil will be dictated by the kind you’re using. Cleaning tank coils enclosed in a metal casing might be tricky.

1. Cleaning Stock Coils

All sub-ohm tanks come with replaceable stock coil heads that can theoretically be cleaned, but not entirely. Cleansing them won’t bring them back to life, but it could offer you a few more days of vaping. The wick material is enclosed within the coil head and wrapped around the coil. Follow this procedure to disinfect your factory-installed coil heads.

  • Immerse your coil in ethanol, vinegar, or cheap vodka for a few hours.
  • Apply soap and water to the coil head.
  • Again, use distilled water to wash your hands.
  • To remove any remaining water from the wicking holes, blow air through the coil on the other side.

2. Cleaning Rebuildable Coils

To keep your RDA or RTA running at its peak performance, it is essential to clean your coils regularly, especially if you are utilizing rebuildable coils.

Clean your rebuildable coil by following these easy steps.

  • Remove your coil’s wicks.
  • Using a low power and being careful not to let the coils glow too much, lightly dry burn them.
  • Remove your device’s atomizer.
  • Please put it in a bowl of warm water and let it soak for a while.
  • Using a coil cleaning tool or toothbrush, gently brush the coils.
  • Refresh the atomizer by giving it another thorough rinse.

Using the techniques outlined above will dramatically extend the life of your coils and tanks. However, if you still notice that the performance is a bit sluggish or that the taste is wrong, it’s time to get a new one.

Related Articles

Leave a Reply

Back to top button